Images fails on my Nano
Xiangfu Liu
xiangfu at sharism.cc
Tue Jan 19 11:48:24 EST 2010
Hi
try the [1] config. cp to /etc/xburst-tools/ rename it to usbboot.cfg.
[1]http://projects.qi-hardware.com/media/upload/xburst-tools/files/usbboot_1GB_nand.cfg
Carlos Camargo wrote:
> Hi
>
> I'm using two old devices (the Chinese dictionary), when I try to upload
> the new images nothing happen :(
>
> Today I download and install the xburst tools, and when I run the
> installer script:
>
> using a 2GB script:
>
> *****************************************************************************************************************
> sudo ./reflash_ben.sh
>
> chosed version: latest
>
> working dir: /tmp/NanoNote/latest
>
> chosed method: http
>
> ===
>
> booting device...
>
> present files are identical to the ones on the server - do not download
> them again
> erase nand rootfs partition...
>
> usbboot - Ingenic XBurst USB Boot Utility
>
> (c) 2009 Ingenic Semiconductor Inc., Qi Hardware Inc., Xiangfu Liu,
> Marek Lindner
> This program is Free Software and comes with ABSOLUTELY NO WARRANTY.
>
> Now checking whether all configure args valid: YES
> Current device information:
> CPU type is Ingenic XBurst Jz4740
> Crystal work at 12MHz, the CCLK up to 252MHz and PMH_CLK up to 84MHz
> SDRAM Total size is 32 MB, work in 4 bank and 16 bit mode
> Nand page per block 128, Nand page size 4096, ECC offset in OOB 12, bad
> block offset in OOB 0, bad block page 127, use 1 plane mode
> Execute command: boot
> CPU data: Boot4740
> Already booted.
> Execute command: nerase 16 1008 0 0
> CPU data: Boot4740
> Erasing No.0 device No.0 flash (start_blk 16 blk_num 1008)......
> Finish! Return: 00 0e 00 00 00 00 01 00 (position 28)
> There are marked bad blocks: -996
> flashing bootloader...
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> flashing kernel...
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:0
> flashing rootfs...
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:0
> done
> **************************************************************************************************************************
>
> Using the original script:
>
> *******************************************************************************************************
> booting device...
> present files are identical to the ones on the server - do not download
> them again
> erase nand rootfs partition...
>
> usbboot - Ingenic XBurst USB Boot Utility
>
> (c) 2009 Ingenic Semiconductor Inc., Qi Hardware Inc., Xiangfu Liu,
> Marek Lindner
> This program is Free Software and comes with ABSOLUTELY NO WARRANTY.
>
> Now checking whether all configure args valid: YES
> Current device information:
> CPU type is Ingenic XBurst Jz4740
> Crystal work at 12MHz, the CCLK up to 252MHz and PMH_CLK up to 84MHz
> SDRAM Total size is 32 MB, work in 4 bank and 16 bit mode
> Nand page per block 128, Nand page size 4096, ECC offset in OOB 12, bad
> block offset in OOB 0, bad block page 127, use 1 plane mode
> Execute command: boot
> CPU data: Boot4740
> Already booted.
> Execute command: nerase 16 1008 0 0
> CPU data: Boot4740
> Erasing No.0 device No.0 flash (start_blk 16 blk_num 1008)......
> Finish! Return: d5 42 49 23 00 00 01 00 (position 4625029)
> There are marked bad blocks: 4624005
> flashing bootloader...
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> flashing kernel...
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:0
> flashing rootfs...
> Error - can't read bulk data from Ingenic device:8
> Error - can't read bulk data from Ingenic device:0
> Error - can't read bulk data from Ingenic device:0
> done
> *********************************************************************************************************
>
>
> --
> Carlos Iván Camargo Bareño
> Profesor Asistente
> Departamento de Ingeniería Eléctrica y Electrónica
> Universidad Nacional de Colombia
> cicamargoba at unal.edu.co <mailto:cicamargoba at unal.edu.co>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Qi Developer Mailing List
> Mail to list (members only): developer at lists.qi-hardware.com
> Subscribe or Unsubscribe: http://lists.qi-hardware.com/cgi-bin/mailman/listinfo/developer
More information about the discussion
mailing list