New images - finally! :)

darcey macinnes dmacinnes at gmail.com
Wed Mar 31 23:53:17 EDT 2010


Hi,

I jumped on IRC and Wolfgang fixed it all for me.

I captured our conversation and will add it to the wiki.

Thanks

On Wed, Mar 31, 2010 at 8:48 PM, Carlos Camargo <cicamargoba at gmail.com>wrote:

> I've compiling the sources using the latest .config file, I've flashed the
> files using:
>
> sudo usbboot -f ./usbboot_2gb_nand.cfg -c "boot"
> sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 0
> openwrt-xburst-u-boot.bin 0 0 -n"
>
>
> #!/bin/bash
>
> KERNEL=/home/cain/Embedded/ingenic/work/Qi/build/openwrt-xburst/bin/openwrt-xburst-uImage.bin
> sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "boot"
> sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 1024 $KERNEL 0 0 -n"
>
> #!/bin/bash
> ROOTFS=openwrt-xburst-qi_lb60-root.ubi
> sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "boot"
> sudo usbboot -f ./usbboot_2gb_nand.cfg  -c "nprog 2048 $ROOTFS 0 0 -n"
>
>
> and all works fine..
>
>
> I make a short cut between the two pads under battery to enter in usbboot
> mode
>
>
> Carlos
>
>
>
>
>
>
>
> On Wed, Mar 31, 2010 at 11:27 PM, Wolfgang Spraul <wolfgang at sharism.cc>wrote:
>
>> > If I connect the device and run lsusb, it is no longer detected.
>> > Suggestions?
>>
>> Can you come to the #qi-hardware irc channel on freenode?
>> A lot faster to solve this kind of problem. Both usbboot and the reflash
>> script are buggy IMHO, I'd say we flash a recent u-boot on your NanoNote
>> and from then on you use boot from microSD to reflash the device.
>> Far more stable, faster, better.
>>
>> If you don't have a dedicated IRC client, this webchat also works:
>> http://webchat.freenode.net/?randomnick=1&channels=qi-hardware
>>
>> Hope to see you there, then we can walk you through... :-)
>> Wolfgang
>>
>> On Wed, Mar 31, 2010 at 07:56:12PM -0700, darcey macinnes wrote:
>> > Ok,
>> >
>> > New problem Xiangfu.  I tried the latest reflash and not only do I still
>> > have the same problem as before, but now I cannot even run the
>> "recovery"
>> > (reflash_ben.sh -b/-k)
>> >
>> > If I connect the device and run lsusb, it is no longer detected.
>> >
>> > Suggestions?
>> >
>> >
>> >
>> > On Wed, Mar 31, 2010 at 5:30 PM, Angus Ainslie <angus at akkea.ca> wrote:
>> >
>> > > On March 31, 2010 06:05:14 pm Xiangfu Liu wrote:
>> > > > Hi
>> > > >
>> > > > we found a bug in the old reflash_ben.sh.
>> > > > now we found that bug. and fixed in the new reflash_ben.sh
>> > > > I just want make sure you are not use the old reflash_ben.sh :-)
>> > > >
>> > >
>> > > Just downloaded the newest one still doesn't work.
>> > >
>> > > > with the old reflash_ben.sh. after reflash the device.
>> > > > we must use this[1] command to make Ben boot.
>> > > >
>> > >
>> > > In one of the earlier emails you said my device would need to boot
>> from a
>> > > 4k
>> > > offset in the boot section. This programming command looks the same as
>> if
>> > > it is
>> > > booting from the 0 offset ?
>> > >
>> > > > the new reflash_ben.sh[2] should work fine.
>> > > >
>> > >
>> > > Nope still doesn't boot
>> > >
>> > > > [1]sudo usbboot -c "boot;nprog 0 openwrt-xburst-u-boot.bin 0 0 -n"
>> > > > [2]
>> > >
>> http://downloads.qi-hardware.com/software/images/Ben_NanoNote_2GB_NAND/r
>> > > > eflash_ben.sh
>> > > >
>> > >
>> > > _______________________________________________
>> > > Qi Developer Mailing List
>> > > Mail to list (members only): developer at lists.qi-hardware.com
>> > > Subscribe or Unsubscribe:
>> > > http://en.qi-hardware.com/mailman/listinfo/developer
>> > >
>> >
>> >
>> >
>> > --
>> > Thank you,
>> >
>> > Darcey MacInnes, CISA CISSP
>>
>> > _______________________________________________
>> > Qi Developer Mailing List
>> > Mail to list (members only): developer at lists.qi-hardware.com
>> > Subscribe or Unsubscribe:
>> http://en.qi-hardware.com/mailman/listinfo/developer
>>
>>
>> _______________________________________________
>> Qi Developer Mailing List
>> Mail to list (members only): developer at lists.qi-hardware.com
>> Subscribe or Unsubscribe:
>> http://en.qi-hardware.com/mailman/listinfo/developer
>>
>
>
>
> --
> Carlos Iván Camargo Bareño
> Profesor Asistente
> Departamento de Ingeniería Eléctrica y Electrónica
> Universidad Nacional de Colombia
> cicamargoba at unal.edu.co
>
> _______________________________________________
> Qi Developer Mailing List
> Mail to list (members only): developer at lists.qi-hardware.com
> Subscribe or Unsubscribe:
> http://en.qi-hardware.com/mailman/listinfo/developer
>



-- 
Thank you,

Darcey MacInnes, CISA CISSP
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.en.qi-hardware.com/pipermail/discussion/attachments/20100331/cf60ce32/attachment.htm>


More information about the discussion mailing list


interactive